06 Bushing SVC Guide - 95.4012.950.000.qxp

For the latest technical information, visit our website at www.rockshox.com. Names used in this manual may be trademarks or registered trademarks of others.
4MB taille 4 téléchargements 268 vues
2006 BUSHING SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit the RockShox website at www.rockshox.com for ordering information. Information contained in this publication is subject to change at anytime without prior notice. For the latest technical information, visit our website at www.rockshox.com. Names used in this manual may be trademarks or registered trademarks of others. © SRAM Corporation • January 2006

PN 95.4012.950.000 Rev A

2006 Bushing Service Guide

WHY DO YOU NEED

TO

REPLACE YOUR SUSPENSION FORK BUSHINGS?

Suspension fork bushings are considered ‘wear and tear’ parts and require regular maintenance, depending on frequency of riding, riding terrain, rider body weight, use of disc brakes, and the type of fork you ride. The more you ride, the more frequently your bushings need to be replaced.

SYMPTOMS

OF

WORN BUSHINGS

• Headset may feel loose • Fork may knock when ridden

CHECK

FOR

LOOSE BUSHINGS

1. Hold the front brake lever tight and rock the bike back and forth. If the fork feels like it’s knocking, or the headset feels loose, proceed to steps 2 and 3. 2. Check the fork: Wrap your fingers around the dust seal and upper tube area. Rock the bike back and forth once again. Listen and feel if there is any play between the upper tube and the dust seal. If so, the bushings are loose. 3. Check the headset: Wrap your fingers around the headset upper cup, or lower cup/race areas. Holding the brake, rock the bike back and forth and feel if the headset is loose. If so, tighten the headset and check again. ROCK BIKE BACK AND FORTH WHILE

1

2

3

SQUEEZING FRONT BRAKE

PA R T S N E E D E D Visit your local SRAM dealer for the tools and parts you will need. If the parts are not in stock, your dealer can place an order with their SRAM distributor. For a more comprehensive list of RockShox spare parts, check out the Spare Parts Catalog at www.rockshox.com or www.sram.com. DUST SEAL KITS 11.4307.250.000

Pilot/SID Dust Seal/Foam Ring Kit

11.4307.298.000

Psylo/Duke Dust Seal/Foam Ring Kit

11.4308.850.000

Reba/Pike Dust Seal/Oil Seal/Foam Ring Kit

11.4307.312.000

Boxxer Dust/Oil Seal Replacement Kit

11.4310.290.000

Tora/Recon/Revel Dust Seal/Foam Ring Kit BUSHING KITS

1

11.4307.251.000

SID, Pilot, Judy Bushing Kit (10mm upr, 20mm lwr)

11.4307.280.000

Duke Bushing Kit (30mm upr/30mm lwr)

11.4307.296.000

Psylo Bushing Kit (30mm upr/45mm lwr)

11.4308.851.000

Reba/Pike/Tora/Recon/Revelation Bushing Kit (30mm upr/30mm lwr)

11.4305.621.000

00-04 Boxxer Bushing Kit (10mm upr/30mm lwr)

11.4310.006.000

05-06 Boxxer Bushing Kit (10mm upr/76mm lwr) © SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide

TOOLS

AND

S TA N D A R D S H O P T O O L S • • • • • • • • • •

Plastic Mallet Oil Pan Work bench with mounted vice 24mm Socket Wrench 22mm Socket Wrench (00-02 Boxxer) 10mm Socket Wrench (All Dual Air forks) 5mm hex wrench Flat-head screw driver Clean rags Oil mixing syringe (MixMizer)

LUBRICANTS NEEDED

LUBRICANTS • • • •

Isopropyl Alcohol/Spray Bottle Oil Soluable Grease 5, 10, or 15wt Suspension Oil Air shock pump (for re-assembly of air forks)

ROCKSHOX BUSHING TOOLKITS Part Number 11.4306.351.000 11.4307.499.000 11.4306.352.000 11.4306.353.000 11.4307.498.000 11.4306.354.000 11.4309.121.000 11.4310.701.000 11.4306.357.000 11.4310.014.000 11.4310.015.000 11.4310.444.000 11.4308.722.000

Description Fork Bushing Removal Tool (28mm/30mm/32mm) Psylo/Duke Bushing Removal Plate (30mm) Fork Bushing Install Tool (28mm/30mm Upr Tube) Fork Bushing Install Tool (32mm Upr Tube) Judy/Pilot/SID Bushing Install Sleeve Psylo/Duke Bushing Install Sleeve Reba/Pike Bushing Install Sleeve Tora/Recon/Revel Bushing Install Sleeve 00-06 Boxxer Bushing Install Sleeve (sleeve only) 05-06 Boxxer Lwr Bushing Install Spacer (used with 00-05 Bushing Install Sleeve) 00-06 Boxxer Bushing Install Sleeve/Spacer (includes Sleeve and 05 Spacer) Dust Seal Install Tool (28mm/30mm) Dust/Oil Seal Install Tool (32mm)

28mm/30mm BUSHING INSTALLATION TOOL PILOT/SID SLEEVE & SPACERS

MALLET DRIFT

Use with: All Forks 11.4306.351.000 Appropriate installation sleeve kit Appropriate installation sleeve kit 11.4306.352.000 11.4306.352.000 11.4306.353.000 11.4306.353.000 11.4306.353.000 11.4306.353.000 & 11.4306.357.000 11.4306.353.000 11.4306.352.000 32mm dust seals, no other tool req’d

32mm BUSHING INSTALLATION TOOL

TORA/RECON/REVELATION SLEEVE & SPACERS

REBA/PIKE SLEEVE & SPACER

BOXXER/REBA/PIKE OIL SEAL/DUST SEAL TOOL

DUKE/PSYLO SLEEVE & SPACERS REBA/PIKE SLEEVE & SPACER

00-05 BOXXER SLEEVE & 05 SPACER

28mm/ 30mm DUST SEAL TOOL

UNIVERAL BUSHING REMOVAL TOOL

28mm 30mm 32mm BUSHING REMOVAL PLATES

95.4012.950.000 Rev A

2

2006 Bushing Service Guide

R E M O VA L : D U S T S E A L S , O I L S E A L S & B U S H I N G S D U S T S E A L , F O A M R I N G, O I L S E A L R E M O VA L SEE

THE APPROPRIATE COMPLETE SERVICE GUIDES FOR FORK DISASSEMBLY AND ASSEMBLY PROCEDURES.

( A L L F O R K M O D E L S : P I L O T, S I D , D U K E , P S Y L O , B O X X E R , R E B A , P I K E , T O R A , R E C O N A N D R E V E L AT I O N ) 1. Using a medium to large flat-head screwdriver, pry the old dust seal from the lower leg. 2. Remove the oil foam ring. Tora/Recon/Revelation and 06 Boxxer include foam rings under the dust seals. 3. Boxxer, Reba, Pike, 2000 and 2001 Judy, 2000-2001 SID and Psylo forks feature an inner oil seal, located just below the dust seal. To remove this oil seal, use a flat-head screwdriver to pry the seal from the lower leg. To protect the lower leg paint, place a rag in between the lower leg and the screwdriver The improved current Samurai dust seal eliminates the need to replace the oil seal. • 2000 - 2002 BOXXER: Remove snap ring and large washer above oil seal.

1a

DUST SEAL REMOVAL

- ALL FORKS

1b

DUST SEAL REMOVAL

- ALL FORKS

2

OIL SEAL REMOVAL

- ALL FORKS

3a

OIL SEAL REMOVAL

- BOXXER

3b

OIL SEAL REMOVAL

- REBA/PIKE

B U S H I N G R E M O VA L - A L L M O D E L S 1. Clamp Bushing Removal Handle/Puller tool into bench vice. Clamp vice tight. 2. Install the correct bushing removal plate onto handle end and secure with handle plate screw. • 28mm Plate (Judy/Pilot/SID) • 30mm Plate (Duke/Psylo) • 32mm Plate (Boxxer/Reba/Pike/Tora/Recon/Revelation) 3. Slide the removal plate past the upper bushing, pull lower leg away from puller, and hook the flat end of the plate secure under the bushing. The removal plate pivots when inserted. When plate is secure under bushing, begin to remove.

1

2

3

REMOVE SCREW TO CHANGE PLATE

BUSHING REMOVAL HANDLE AND PLATE

3

32mm

30mm

28mm

REMOVAL PLATE

REMOVAL PLATE

REMOVAL PLATE

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide 3. To pull the upper bushing free from the lower leg use a plastic mallet to firmly and sqaurely hit the top of the lower leg on the flat dust seal surface area until upper bushing pulls free. BOXXER - Follow same procedure for Boxxer lower leg upper bushing and lower bushing removal.

SID/Pilot

Duke

Psylo

Reba/Pike

Tora/Recon/RVL

SID/Pilot

Duke

Psylo

Reba/Pike

Tora/Recon/RVL

4. To pull the lower bushing free from the lower leg, slide the removal plate past the lower bushing, and hook the flat end of the plate secure under the bushing. Again, firmly hit the top of the lower leg (flat dust seal surface) until bushing pulls free. Longer lower bushings require more force. 5. Repeat other side. Wipe off any debris from lower leg inner surface.

SID/Pilot

Duke

Psylo

Reba/Pike

Tora/Recon/RVL

SID/Pilot

Duke

Psylo

Reba/Pike

Tora/Recon/RVL

B U S H I N G I N S TA L L AT I O N B U S H I N G I N S TA L L AT I O N : ( 0 0 - 0 2 J U D Y / 0 3 - 0 5 P I L O T / 9 9 - 0 6 S I D ) - 2 8 M M L O W E R B U S H I N G I N S TA L L AT I O N : 2 8 M M 1. 2. 3. 4. 5.

X

WIDTH

20MM

Clamp 28mm/30mm bushing installation tool into bench-mounted vice. Slide lower 28mm Pilot/SID bushing sleeve onto bushing installation post. Slide 20mm lower bushing onto top of lower bushing installation sleeve. Slide lower leg over installation post and rest on top of lower bushing. Insert the mallet drift tool into the lower leg shaft hole, and hold in place with one hand.

95.4012.950.000 Rev A

4

2006 Bushing Service Guide 6. Using a plastic mallet, hit the drift to press the bushing into the lower leg. Hit the drift until the lower leg dust seal ridge is level with the top of the installation post spacer. Stop and remove lower leg from tool. 7. Inspect the fit of the lower bushing by sliding one upper tube into the lower leg. Hold lower leg 90 degrees horizontally and release. Lower leg should swing 45 degrees down and stop. If the lower leg swings as described move on to upper bushing or install lower bushing on the other side. If the lower leg swings too freely, repeat step 6. 8. If lower leg does not swing at all or feels tight, slide lower leg back onto bushing installation bushing post and rock side to side to loosen fit. NOTE: SID LOWER LEG PICTURED. SAME PROCEDURE FOR 03-05 PILOT AND 00-02 JUDY. SID/PILOT LOWER

1

2

3

4

6

BUSHING INSTALLATION

SID/PILOT 20mm LOWER

SLEEVE

BUSHING CLAMP

28MM/30MM

INSTALLATION

STOP

PLATE/POST TOOL, TAPERED EDGE ALIGNED WITH END

FLUSH WITH POST STEP

OF VICE.

U P P E R B U S H I N G I N S TA L L AT I O N : 2 8 M M

X

10MM

1. 2. 3. 4.

Remove lower bushing installation sleeve from bushing installation post. Slide 10mm (first) and 5mm Judy/Pilot/SID upper bushing installation spacers onto bushing installation post, as pictured. Slide 10mm upper bushing onto bushing installation post. Bushing will rest on top of 5mm spacer. Slide lower leg over installation post and rest on top of upper bushing. Insert mallet drift tool into the lower leg shaft hole and hold in place. Using a plastic mallet, hit the mallet drift to press the bushing into the lower leg. 5. Hit the drift until the lower leg dust seal ridge is flush with the 5mm installation spacer. You will feel the stop point as the bushing is ‘set’ into lower leg. 6. Remove lower leg from tool and inspect upper bushing. The upper bushing should be flush with the top of the dust seal counter bore step. Do not press bushing below bore step. It is best to tap the bushing in then remove lower leg and check the fit. Tap lower leg until dust seal surface is even with lower step of post step. 7. Repeat other side. NOTE: SID LOWER LEG PICTURED. SAME PROCEDURE FOR PILOT AND 00-02 JUDY.

1

2

3

4

5

10mm UPPER BUSHING

10mm

5mm

STOP

SPACER

SPACER FLUSH WITH POST STEP. LOWER LEG WILL STOP ON

5

5MM

SPACER.

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide B U S H I N G I N S TA L L AT I O N : D U K E - 3 0 M M L O W E R B U S H I N G I N S TA L L AT I O N : 3 0 M M

X

WIDTH

30MM

1. Slide lower 15mm Duke lower bushing sleeve spacer (for 30mm lower bushing) onto installation post. Slide the long Duke/Psylo lower bushing sleeve onto bushing installation post. The sleeve will rest on top of 15mm spacer. 2. Slide 30mm slotted bushing (thin-walled) onto top of lower bushing installation sleeve. 3. Slide Duke lower leg over installation post, and rest on top of lower bushing. 4. Insert the mallet drift tool into the lower leg shaft hole and hold in place. Using the plastic mallet, hit the mallet drift tool to press the bushing into lower leg. 5. Hit the drift until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point as the bushing is ‘set’ into the lower leg. 6. Repeat on other side.

SLOTTED SLOTTED THIN WALL

WALL

LOWER BUSHING

DUKE/PSYLO LOWER BUSHING

1

2

NON-SLOTTED THICK

3

UPPER BUSHING

4

5

SLEEVE

30mm DUKE

15mm

LOWER

DUKE

BUSHING

SLEEVE SPACER

U P P E R B U S H I N G I N S TA L L AT I O N : 3 0 M M

X

30MM

1. Remove Duke lower bushing sleeve and spacer from bushing installation post. 2. Slide Duke/Psylo upper bushing installation sleeve onto bushing installation post. Bushing will rest on top of Duke/Psylo upper installation sleeve. 3. Slide 30mm Duke (thick-walled) upper bushing onto bushing installation post. Bushing will rest on top of Duke/Psylo upper bushing installation sleeve. 4. Slide Duke lower leg over installation post and rest on top of upper bushing. 5. Insert the mallet drift tool into the lower leg shaft hole and hold in place. Using the plastic mallet, hit the mallet drift tool to press the bushing into lower leg. 6. Hit the drift until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. 7. Remove lower leg, and check bushing. Upper bushing should be flush with top of dust seal counter-bore step. 8. Repeat on other side.

2

3

4

5

6

PSYLO UPPER DUKE/PSYLO

BUSHING

UPPER BUSHING INSTALLATION SLEEVE

95.4012.950.000 Rev A

6

2006 Bushing Service Guide B U S H I N G I N S TA L L AT I O N : P S Y L O - 3 0 M M L O W E R B U S H I N G I N S TA L L AT I O N : 3 0 M M IMPORTANT:

45MM

LOWER BUSHING IS NOT COMPATIBLE WITH

LEGS, REPLACE LOWER LEG ASSEMBLY WITH

2004

2001

X

WIDTH

45MM

SLOTTED

PSYLO LOWER LEGS. FOR

2001

PSYLO LOWER

LOWER LEG ASSEMBLY IF BUSHINGS NEED TO BE REPLACED.

1. 2. 3. 4.

Slide the Duke/Psylo lower bushing sleeve onto bushing installation post. Slide 45mm slotted bushing (thin-walled) onto top of lower bushing installation sleeve. Slide Psylo lower leg over installation post, and rest on top of lower bushing. Insert the mallet drift tool into the lower leg shaft hole, and hold in place. Using the plastic mallet hit the mallet drift tool to press the bushing into lower leg. 5. Hit the drift until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. 6. Repeat on other side. 45mm

PSYLO

LOWER

2

3

4

5

BUSHING

30mm DUKE/PSYLO LOWER BUSHING INSTALLATION SLEEVE

U P P E R B U S H I N G I N S TA L L AT I O N : 3 0 M M

X

30MM

( C O M PAT I B L E

WITH ALL PSYLO LOWER LEGS)

1. Remove Duke/Psylo lower bushing sleeve from bushing installation post. 2. Slide Duke/Psylo upper bushing installation sleeve onto bushing installation post, thin side up. 3. Slide 30mm Psylo upper bushing (thick-wall bushing) onto bushing installation post. Bushing will rest on top of bushing installation sleeve. 4. Slide lower leg over installation post, and rest on top of upper bushing. 5. Insert mallet drift tool into Psylo lower leg shaft hole, and hold in place. Using a plastic mallet, hit the mallet drift tool to press the bushing into the lower leg. 6. Hit the drift until the lower leg dust seal ridge is flush with the installation post plate. You will feel the stop-point as the bushing is ‘set’ into lower leg. 7. Remove lower leg from post tool and check upper bushing. Bushing should be flush with the top of the dust seal counterbore step. 8. Repeat other side.

2

3

4

5

6

PSYLO UPPER DUKE/PSYLO

BUSHING

UPPER BUSHING INSTALLATION SLEEVE

7

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide B U S H I N G I N S TA L L AT I O N : R E B A / P I K E - 3 2 M M L O W E R B U S H I N G I N S TA L L AT I O N : 3 2 M M (PIKE

X

30MM -

WIDTH SLOTTED

PICTURED, SAME PROCEDURE FOR PIKE AND REBA)

1. 2. 3. 4. 5. 6.

Slide the Reba/Pike lower bushing sleeve spacer onto 32mm bushing installation post. Slide Reba/Pike lower bushing installation sleeve on 32mm bushing installation post. Slide Reba/Pike 30mm thick slotted lower bushing onto the top of the lower installation sleeve. Slide lower leg over installation post and rest on top of lower bushing. Reba: Insert mallet drift tool into the lower leg shaft hole and hold in place. (not pictured) Using a plastic mallet, hit the bottom of the lower leg (Pike), or the mallet drift tool (Reba) to press the bushing into the lower leg. 7. Hit the lower leg, or mallet drift, until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point as the bushing is ‘set’ into the lower leg. 8. Repeat on other side.

1

REBA/PIKE/TORA/RE

2

3

6

7

CON/RVL LOWER BUSHING INSTALLATION SLEEVE

REBA/PIKE

REBA/PIKE/ TORA/RECON/

BUSHING

RVL LOWER

INSTALLATION

BUSHING

SPACER

-

SLOTTED

U P P E R B U S H I N G I N S TA L L AT I O N : 3 2 M M (PIKE

X

30MM -

NON SLOTTED

PICTURED, SAME PROCEDURE FOR PIKE AND REBA)

1. 2. 3. 4.

Remove Reba/Pike lower bushing sleeve. Leave lower bushing spacer on installation post/base tool. Slide 30mm Reba/Pike upper bushing (non-slotted) onto 32mm bushing installation post. Slide lower leg over installation post, and rest on top of the upper bushing. Reba: Insert mallet drift tool into the lower leg shaft hole and hold in place. (not pictured) 5. Using the plastic mallet, hit the mallet drift tool (Reba), or bottom of lower leg (Pike), to press 30mm REBA/PIKE/TORA the upper bushing into lower leg. /RECON/RVL UPPER BUSHING 6. Hit the drift until the lower leg rests flush on top of install spacer. You will feel the stoppoint as the bushing is ‘set’ into the lower leg. REBA/PIKE BUSHING Remove the lower leg from the installation INSTALLATION SPACER post, and check the bushing fit. The top of the bushing should be flush/level with oil seal step in the lower leg. 7. Repeat on other side.

2

95.4012.950.000 Rev A

5

6

8

2006 Bushing Service Guide B U S H I N G I N S TA L L AT I O N : T O R A / R E C O N / R E V E L AT I O N - 3 2 M M L O W E R B U S H I N G I N S TA L L AT I O N : 3 2 M M (ALL

U S E T H E S A M E L O W E R L E G A S S E M B LY .

X

30MM -

WIDTH

SLOTTED

PROCEDURE IS THE SAME FOR ALL THREE)

1. 2. 3. 4. 5. 6.

Slide the Reba/Pike/Tora/Recon/Revelation lower bushing sleeve spacer onto 32mm bushing installation post. Slide the Reba/Pike/Tora/Recon/Revelation short lower bushing installation spacer on 32mm bushing installation post). Slide the Tora/Recon/Revelation tall lower bushing spacer onto the 32mm bushing installation post. Slide Reba/Pike/Tora/Recon/Revelation 30mm thick slotted lower bushing onto the top of the lower installation sleeve. Slide lower leg over installation post and rest on top of lower bushing. Insert mallet drift tool into the lower leg shaft hole and hold in place. Using a plastic mallet, hit the bottom of the lower leg mallet drift tool to press the bushing into the lower leg. 7. Hit the lower leg, or mallet drift, until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point as the bushing is ‘set’ into the lower leg. 8. Repeat on other side.

1

2

REBA/PIKE/TORA/RECON/RVL

REBA/PIKE/TORA/RECON/RV L

-

-

LOWER BUSHING

TORA/RECON/ RVL

4

-

7

-

INSTALLATION SPACER

-

TALL

SHORT

U P P E R B U S H I N G I N S TA L L AT I O N : 3 2 M M (ALL

5 &6

LOWER BUSHING

LOWER BUSHING

INSTALLATION SPACER

INSTALLATION SLEEVE

3

X

30MM -

NON SLOTTED

U S E S A M E L O W E R L E G A S S E M B LY . P R O C E D U R E I S T H E S A M E F O R A L L T H R E E )

1. Remove Reba/Pike/Tora/Recon/Revelation lower bushing sleeve and tall Tora/Recon/RVL installation spacer. Leave lower bushing spacer on installation post/base tool. 2. Slide 30mm Reba/Pike/Tora/Recon/Revelation upper bushing (non-slotted) onto 32mm bushing installation post. 3. Slide lower leg over installation post, and rest on top of the upper bushing. 4. Insert mallet drift tool into the lower leg shaft hole and hold in place. Using the plastic mallet, hit the mallet drift tool to press the upper bushing into lower leg. 6. Hit the drift until the lower leg rests flush on top of install spacer. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. Remove the lower leg from the installation post, and check the bushing fit. The top of the bushing should be flush/level with oil seal step in the lower leg. 7. Repeat on other side.

2

3

3

4

6

REBA/PIKE/TORA/ RECON/RVL

-

UPPER BUSHING INSTALLATION SPACER

9

REBA/PIKE/TORA

/RECON/RVL UPPER BUSHING

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide B U S H I N G I N S TA L L AT I O N : B O X X E R - 3 2 M M L O W E R B U S H I N G I N S TA L L AT I O N : 3 2 M M NOTE:

05-06 76MM

LOWER BUSHINGS ARE NOT COMPATIBLE WITH

PREPARATION: CLAMP THE

32MM

X

WIDTH

30MM (2000-2004)

2000-2004

BOXXER LOWER LEGS.

BUSHING INSTALLATION POST TOOL INTO VICE.

1. 2. 3. 4. 5. 6.

Slide the Boxxer lower bushing installation sleeve onto bushing installation post. Slide 30mm lower bushing onto top of lower bushing installation sleeve. Slide Boxxer lower leg over installation post, and rest on top of lower bushing. Insert the mallet drift tool into the lower leg shaft hole, and hold in place.. Using the plastic mallet, hit the mallet drift tool to press the bushing into lower leg. Hit the drift until the lower leg dust seal ridge is level with the top of the installation post spacer. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. 7. Repeat on other side.

1

2

BOXXER

BOXXEr

LOWER

30mm

BUSHING

LOWER

INSTALLATION

BUSHING

3

4

6

SLEEVE

L O W E R B U S H I N G I N S TA L L AT I O N : 3 2 M M IMPORTANT: THE

76MM

X

76MM (2005-2006)

BOXXER LOWER BUSHING IS NOT COMPATIBLE WITH THE

PREPARATION: CLAMP THE

32MM

2000-2004

BOXXER LOWER LEG.

BUSHING INSTALLATION POST TOOL INTO VICE.

1. Slide the Boxxer lower bushing sleeve and 76mm Boxxer lower bushing installation spacer over post tool, and rest on bottom of plate. 2. Slide 76mm lower bushing on top of lower bushing installation sleeve. 3. Slide Boxxer lower leg over installation post, and rest on top of lower bushing. 4. Insert the mallet drift tool into the lower leg shaft hole, and hold in place. Using the plastic mallet, hit the mallet drift tool to press the bushing into lower leg. 5. Hit the drift until the lower leg dust seal ridge is flush with the top of the installation post spacer. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. 6. Repeat on other side.

1

1

2

3

4

5

BOXXER LOWER BUSHING INSTALLATION

BOXXER

SLEEVE

76mm LOWER BUSHING INSTALLATION SPACER

95.4012.950.000 Rev A

BOXXER

76mm LOWER BUSHING

10

2006 Bushing Service Guide U P P E R B U S H I N G I N S TA L L AT I O N : 3 2 M M

X

10MM

1. Remove Boxxer lower bushing sleeve and 05/06 lower bushing spacer (if used on 05/06 Boxxer lower leg) from Boxxer bushing installation post. 2. Slide 10mm Boxxer upper bushing onto Boxxer bushing installation post. 3. Slide lower leg over installation post and rest on top of upper bushing. 4. Insert Boxxer mallet drift tool into the lower leg shaft hole and hold in place. Using the plastic mallet, hit the mallet drift tool to press the upper bushing into lower leg. 5. Hit the drift until the lower leg dust seal ridge is flush with the upper bushing/oil seal step in the lower leg. The ‘stop-point’ on the post tool is about 5mm above the plate. You will feel the stop-point, as the bushing is ‘set’ into the lower leg. Remove the lower leg from ths installation post, and check the bushing fit. The top of the bushing should be flush/level with oil seal step in the lower leg. 6. Repeat on other side.

2

3

4

5

10mm UPPER BUSHING

STOP

I N S TA L L AT I O N : D U S T S E A L S & F O A M R I N G S JUDY/PILOT/SID/DUKE/PSYLO - 28MM/30MM (SID

1. 2. 3. 4. 5. 6. 7. 8.

LOWER LEG PICTURED.

WIDTH

S A M E P R O C E D U R E F O R P I L O T, D U K E A N D P S Y L O . )

Soak new foam rings in 5, 10 or 15wt suspension oil. Slide 28mm/30mm Dust Seal Installation Tool over 28mm/30mm Bushing Installation Post tool. Slide new dust seal over bushing installation post tool and fit on top of Dust Seal Installation tool. Slide oil-saturated foam ring over bushing installation post tool and fit on top of dust seal. Seat the foam ring inside the under cavity of dust seal. Using a clean rag and isopropyl alcohol, clean the inside of the dust seal area of the lower leg. Slide lower leg onto bushing installation post, on top of new dust seal. Using a plastic mallet, lightly tap on the lower leg drop-out until dust seal seats inside lower leg, flush with the top of lower leg dust seal step. Dust seal should be press-fit snug into the lower leg. Repeat on other side.

1

2

3 DUST SEAL

28mm/30mm DUST SEAL

28mm 30mm

3

3

-

OR

INSTALLATION TOOL

102

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE

2006 Bushing Service Guide

4

4

6

5

6

OIL SATURATED FOAM RING

REBA/PIKE/BOXXER (INCLUDES O I L S E A L I N S TA L L AT I O N

(BOXXER

OIL SEAL)

PICTURED SAME PROCEDURE FOR REBA AND PIKE)

1. Apply grease or 15wt suspension oil to the inside of the Reba, Pike or Boxxer lower leg oil seal counter-bore. 2. Insert the oil seal onto the stepped end of the 32mm Oil Seal Installation tool. 3. Using the 32mm Oil Seal Installation tool, insert the oil seal down and into the oil step in the lower leg. Apply pressure on all sides of the oil seal to seat it into place. BOXXER NOTE: THE

2000-2002 OIL SEAL WASHER AND SNAP RING ARE NO LONGER REQUIRED WHEN REPLACING OIL AND DUST SEALS. 2006 DUST SEAL KITS DO NOT INCLUDE THE OIL SEAL WASHER AND SNAP RING.

NO NEED TO RE-INSTALL.

F O A M R I N G I N S TA L L AT I O N

4. REBA/PIKE/BOXXER: Insert new oil-saturated foam ring into lower leg and on top of newly installed oil seal. BOXXER: 2006 Dust Seal kits include foam rings and are compatible with all Boxxer lower legs assemblies. D U S T S E A L I N S TA L L AT I O N

5. Insert new dust seal into the opposite (wide) end of the 32mm dust seal installation tool. 6. Insert dust seal into lower leg and press straight down evenly to seat into lower leg. 7. Dust seal should be press-fit snug and flush into lower leg. NOTE: CHECK FOAM RING UNDER DUST SEAL. FOAM RING SHOULD NOT PROTRUDE FROM DUST SEAL AND OIL RING. IF SO, ADJUST FOAM RING INSIDE LOWER LEG, FLUSH ALL ON SIDES.

8. Repeat on other side.

1

95.4012.950.000 Rev A

2

3

3

5

12

2006 Bushing Service Guide

6

7

T O R A / R E C O N / R E V E L AT I O N ( N O

7

OIL SEAL)

F O A M R I N G I N S TA L L AT I O N :

1. Insert new oil-saturated foam ring into lower leg. D U S T S E A L I N S TA L L AT I O N :

2. Insert new dust seal into the wide open end of the 32mm dust seal installation tool. 3. Insert dust seal into lower leg and press straight down evenly to seat into lower leg. 4. Dust seal should be press-fit snug and flush into lower leg. NOTE: CHECK FOAM RING UNDER DUST SEAL. FOAM RING SHOULD NOT PROTRUDE FROM DUST SEAL AND OIL RING. IF SO, ADJUST FOAM RING INSIDE LOWER LEG, FLUSH ALL ON SIDES.

5. Repeat on other side.

1

2

FINISHING UP 1. 2. 3. 4.

13

2

3

3

4

4

Spray entire completed lower leg assembly with isopropyl alcohol. Wipe lower leg assembly clean with a rag. Check decals and replace if necessary. Refer to the ‘Lower Leg Removal and Installation Service Guide’ or individual fork model service guides for installation procedures.

© SRAM Corporation • 2006 BUSHING SERVICE GUIDE