[ Guidance of harness connection ] P1

+BATT power (after IG switch) wiring(orange) is connected with the wiring where the +batt power is supplied when the IG key switch is turned on. In the case of ...
395KB taille 8 téléchargements 311 vues
[ G uidance of harness connection ] engine side

E x te rn a ls o f th e h a rn e s s

boost sensor w iring *1 throttle sensor w iring Injector w iring

tem perature sensor w iring

signal interface w iring

"dial controller" w iring

E C U *2 connector

pum p w iring

ground (0V ) w iring (w ith round term inal)

*1 D -JE tronic V ersion O nly *2 E C U : E lectoronic C ontrol U nit

(1)

P lease decide the position w here each unit is installed.

(2)

P lease install each unit, and fix.

(3)

P lease fix the harness to the vehicle by using the band etc.

backup pow er(+ BATT) w iring

+ B A T T pow er (after IG sw itch) w iring

T he harness kit is designed so that E C U is installed at the center of the vehicle.

P1

[ G uidance of harness connection ] * A tte n tio n : P le a s e re m o v e th e te rm in a l fro m th e b a tte ry b e fo re b e g in n in g in s ta llin g . * A tte n tio n : P le a s e c o n n e c t a n o ra n g e , re d w irin g to th e lin e a fte r th e fu s e .

(4)

+B A TT pow er (after IG sw itch) w iring(orange) is connected w ith the w iring w here the +batt pow er is supplied w hen the IG key sw itch is turned on. In the case of H onda M onkey,"IG " line is usually in the m eter case(front light case).

In the M eter (front light) case.

T w o connectors ( for + B A T T IG and + B A T T -backup) are in this kit. (use If you w ant.)

+ B A T T pow er (after IG sw itch) cable (orange)

[ G uidance of harness connection ] (5)

P lease connect red w iring (red) w ith the line connected w ith the plus term inal of the battery. (A fter off the key, this pow er supply is used for E C U only betw een a few seconds. A fterw ards, this pow er supply is not used. EC U doesn`t need an extra standby pow er requirem ent. )

(6)

P lease install the earth connection line (w ith round term inal) in the earth of the body (battery m inus).

(7)

P lease confirm not be w rong the connection of the plus and the m inus of w iring.

C onnecting red w iring to the plus line of battery.

red w iring : + batt (back up pow er) earth connection w iring (w ith round term inal)

P3

[ G uidance of harness connection ] (8)

P lease connect each unit to the w iring connector.

throttle sensor (3pins connector)

dial controller (6pins connector)

injector (2pins gray connector)

E C U connector (8pins and 10pins connector)

dial controller

P4

[ G uidance of harness connection ] (8)

P lease connect each unit to the w iring connector.

signal interface unit ( 4pins connector w ith light-purple w iring)

P lease connect fem ale connector of light-purple w iring to the (+) term inal of ignition coil,and conect the vehicle w iring, connected w ith the coil (+) term inal originally, to the m ale connector of light-purple w iring. In the case of H O N D A M O N K E Y(current m odel),coil(+) term inal color is green. *P lease contact m e w hen you w ant to use it w ith a beam type tim ing sensor.

(eco-run vehicle etc.)

fuel pum p w iring P lease connect pink and w hite w iring to connector of fuel pum p. pink w iring is (+), w hite w iring is (-). *If you don't need that the fuel pum p is not controlled by E C U , it is necessary to obtain the dum m y resistance. ( eco-run etc.)

P5

[ G uidance of harness connection ] (9)

First of all, please confirm the connection of w iring (E specially, (+) and (-) connection of the pow er supply). P lease turn on the pow er (IG ) sw itch after confirm ing. W hen EC U starts norm ally, the pum p is driven about ten tim es by the pulse, and dial controller's LE D turns on. P lease do initializing referring to (3) "configure and adjustm ent " chapter of the user's m anual. *W hen you bought the throttle body from us at the sam e tim e, the adjustm ent of the throttle sensor and the setting of the capacity of the injector have already been done. If you have already inform ed "FC design" of the displacem ent of the engine, a rough adjustm ent of the injection m ap is done. *P le a s e re fe r to " S ta rt-u p m a n u a l" fo r th e a d ju s te d c o n te n t.

D-jetronic ( speed density version ) Please connect boost ( manifold pressure ) sensor.

P6